在隔热断桥铝型材制造中，开齿穿条机是一种用于在铝型材上进行加工的设备。它主要用于在铝型材的隔热断桥部位开槽，并为隔热条的安装提供准确的穿孔。下面由有十多年的机器研发经验的济南歌德瑞斯机械设备为您带来开齿机穿条机的相关知识。

In the manufacturing of thermal insulation broken bridge aluminum profiles, the toothed threading machine is a device used for processing on aluminum profiles. It is mainly used for slotting the insulation bridge section of aluminum profiles and providing accurate perforation for the installation of insulation strips. Below, Jinan Gede Ruisi Mechanical Equipment, with over ten years of experience in machine research and development, will bring you relevant knowledge about gear cutting and threading machines.

　　开齿穿条机的保养知识：

Maintenance knowledge of toothed threading machine:

　　为保证机器的良好运行，在运行过程中若有异常情况应立即停车检查。排除故障后再重新启动。设备出现较大的的故障时应有专业人士来维修，在开始检修前切忌关掉总电源。

To ensure the good operation of the machine, if there are any abnormal situations during operation, it should be stopped immediately for inspection. After troubleshooting, restart. When there is a major malfunction in the equipment, it should be repaired by professionals. Before starting maintenance, it is important to avoid turning off the main power supply.

　　1、传动维护： 各传送辊轴承、毛刷辊轴承、传送轴承、链轮、齿轮定期加注钙基润滑脂；微型摆线针轮减速机每半年加钙基润滑脂一次；无级调速器每半年换Ub—l或Ub—3型润滑油一次，且在运转过程中应时常检查其油位，保持油位在滑标中心线以上。

1. Transmission maintenance: Regularly add calcium based lubricating grease to the bearings of each conveyor roller, brush roller, conveyor bearing, sprocket, and gear; Add calcium based grease to the micro cycloidal gear reducer every six months; The stepless speed controller should replace Ub-l or Ub-3 lubricating oil every six months, and its oil level should be checked regularly during operation to keep it above the centerline of the sliding mark.

　　2、水路维护： 水箱内循环水应每天更换，水箱每周清洗一次，经常检查喷水嘴喷水情况，项发现堵塞应及时清理。

2. Waterway maintenance: The circulating water in the water tank should be replaced every day, and the water tank should be cleaned once a week. The spray nozzle should be checked regularly for water spraying, and any blockage should be cleaned in a timely manner.

　　3、风路维护： 定期检查中空玻璃生产线风机运行情况，如有异常声音应立即停机检查，定期清洗风机过滤栅，减小引风阻力，提高风干后玻璃表面洁净度。

3. Wind path maintenance: Regularly check the operation of the fans in the insulated glass production line. If there is any abnormal sound, stop the machine immediately for inspection. Regularly clean the filter screen of the fan to reduce the induced air resistance and improve the cleanliness of the glass surface after drying.

本文由 开齿穿条机 为您精心提供，如想了解更多请点击我们的网站：https://www.jnsaiwo.com，我们将会以最大的热情为您解答!

This article is carefully provided by a toothed threading machine. If you want to learn more, please click on our website: https://www.jnsaiwo.com We will answer you with the greatest enthusiasm!