电源：断桥铝门窗设备的公共电压为380V，接线时需要注意带电与零线的连接。一般来说，门窗设备制造商会区分不同的颜色。一般来说，带电导线为黑色或蓝色，零线为红色(取决于每个制造商的情况)。如果带电导线反向连接，则只需更换带电导线两端的两根导线。

Power supply: The common voltage of the broken bridge aluminum door and window equipment is 380V. When wiring, attention should be paid to the connection between live and neutral lines. Generally speaking, door and window equipment manufacturers will distinguish different colors. Generally speaking, the live wire is black or blue, and the neutral wire is red (depending on the situation of each manufacturer). If the live wire is connected in reverse, only the two wires at both ends of the live wire need to be replaced.

　　气源：由于断桥铝门窗设备的压料由气瓶压缩，特别是断桥铝型材加工切割锯、断桥铝型材端铣机、断桥铝型材角码锯。确保充足的空气供应是设备使用的前提。气压不足会影响断桥铝型材双头切割锯的锯片，从而影响其加工效果。

Gas source: Due to the compression of the pressure material of the broken bridge aluminum door and window equipment by gas cylinders, especially the cutting saw for processing broken bridge aluminum profiles, the end milling machine for broken bridge aluminum profiles, and the angle saw for broken bridge aluminum profiles. Ensuring sufficient air supply is a prerequisite for the use of equipment. Insufficient air pressure can affect the saw blade of the double end cutting saw for broken bridge aluminum profiles, thereby affecting its processing efficiency.

　　一般来说，一套断桥铝门窗设备可以保证风压达到8压，风量达到0.3。如果设备太多，仅仅依靠空气泵是不够的。你需要准备一到两个油箱。

Generally speaking, a set of broken bridge aluminum door and window equipment can ensure a wind pressure of 8 and an air volume of 0.3. If there are too many devices, relying solely on air pumps is not enough. You need to prepare one to two fuel tanks.

　　空压机：检查空压机连接是否牢固，防止漏气。

Air compressor: Check if the connection of the air compressor is firm to prevent air leakage.

　　设备部件：铝门窗断桥设备种类较多，每种类型设备种类较多。因此，检查门窗加工设备尤其重要，如切割锯的气管塞、锯片的进出口、锯头的左右工作状态等，调整门窗加工设备切割锯片的进给速度。调试时，如果锯片进给速度过快或过慢，可调整门窗设备进给缸上的调速阀，以获得合适的进给速度。

Equipment components: There are many types of aluminum door and window bridge breaking equipment, and each type of equipment has a variety of types. Therefore, it is particularly important to check the door and window processing equipment, such as the gas pipe plug of the cutting saw, the inlet and outlet of the saw blade, and the left and right working status of the saw head, and adjust the feed rate of the cutting saw blade of the door and window processing equipment. When debugging, if the feed speed of the saw blade is too fast or too slow, the speed control valve on the feed cylinder of the door and window equipment can be adjusted to obtain the appropriate feed speed.

以上就是有关：开齿穿条机 的介绍，想了解更多的内容请点击：https://www.jnsaiwo.com 我们将会全心全意为您提供满分服务，欢迎您的来电！

The above is an introduction to the toothed threading machine. To learn more, please click: https://www.jnsaiwo.com We will wholeheartedly provide you with full score service. Welcome to call us!