穿条机启动不了可能有多种原因，以下是一些可能的故障原因及其解决方法：

　　There may be multiple reasons why the strip threading machine cannot start. Here are some possible causes of the malfunction and their solutions:

　　1. 外部总电源未接通：检查外接电源是否连接正常，确保电源线没有损坏，重新送电。

　　1. External main power supply not connected: Check if the external power supply is connected properly, ensure that the power cord is not damaged, and re power on.

　　2. 内部控制电源未接通：使用钥匙开关打开电源或合上配电柜内的开关。

　　2. Internal control power not connected: Use the key switch to turn on the power or close switch 1 inside the distribution cabinet.

　　3. 暂停按钮按下不起：检查暂停按钮是否被按下，如果按下，尝试再按一下让它弹起复位。

　　3. Pause button cannot be pressed: Check if the pause button is pressed. If it is pressed, try pressing it again to make it pop up and reset to .

　　4. 急停按钮按下：检查急停按钮是否被按下，如果按下，放开急停按钮。

　　4. Emergency stop button pressed: Check if the emergency stop button is pressed. If it is pressed, release emergency stop button .

　　5. PLC损坏：如果PLC（可编程逻辑控制器）损坏，建议重新更换。

　　5. PLC damage: If the PLC (programmable logic controller) is damaged, it is recommended to replace it with a new one.

　　6. 保险丝烧坏：检查保险丝是否烧坏，如果烧坏，建议更换保险丝。

　　6. Fuse burnt out: Check if the fuse is burnt out. If it is burnt out, it is recommended to replace fuse .

　　7. 电源线与其他设备损怀：检查电源线是否与其他设备有损坏或干扰，重新接独立电源。

　　7. Damage to power cord and other devices: Check if the power cord is damaged or interferes with other devices, and reconnect the independent power supply .

　　4d33737a6bf7dd9

　　8. 变频器缓起启动设置过长：如果自动缠绕机转盘需要人推才能启动，可能是变频器缓起启动设置的起动时间太长，重新设定。

　　8. The slow start setting of the frequency converter is too long: If the automatic winding machine turntable requires human pushing to start, it may be due to the slow start setting of the frequency converter being too long. Reset .

　　9. 拨码开关损坏：检查拨码开关是否损坏，如果损坏，则检修拨码开关。

　　9. Damaged dip switch: Check if the dip switch is damaged. If it is damaged, repair dip switch .

　　10. 转盘链条断裂：检查转盘链条是否断裂，调整大小链轮之间的距离，连接链条，如果是链条损坏则更换链条。

　　10. Broken turntable chain: Check if the turntable chain is broken, adjust the distance between the size chain wheels, connect the chain, and if the chain is damaged, replace chain .

　　11. 转盘电机或减速机故障：检查转盘电机和减速机是否工作正常，如有故障，建议更换。

　　11. Fault in turntable motor or reducer: Check if the turntable motor and reducer are working properly. If there is a fault, it is recommended to replace them.

　　12. 旋钮损坏：检查旋钮是否损坏，如果是，更换旋钮。

　　12. Knob damage: Check if the knob is damaged, and if so, replace knob .

　　13. 转盘减速机与链轮连接不正常：检查连接是否正常，换连接平键。

　　13. The connection between the turntable reducer and the sprocket is abnormal: check if the connection is normal and replace it with the flat key .

　　14. 变频器显示过载报警：如果变频器显示过载报警，检查电压是否稳定，改善电源品质或调整变频加减速时间。

　　14. Overload alarm displayed on the frequency converter: If the frequency converter displays an overload alarm, check if the voltage is stable, improve the quality of the power supply, or adjust the acceleration and deceleration time of the frequency converter.

　　如果上述方法都不能解决问题，建议联系专业的维修人员进行检查和维修。在进行维修时，请确保安全第一，避免因操作不当造成人身伤害或设备进一步损坏。

　　If none of the above methods can solve the problem, it is recommended to contact professional maintenance personnel for inspection and repair. When carrying out repairs, please ensure safety first and avoid personal injury or further damage to equipment caused by improper operation.

　　本文由穿条机提供帮助，更多的相关内容请点击：https://www.jnsaiwo.com希望本文能够为您带来帮助，感谢您的阅读！

　　This article is assisted by the threading machine. For more related content, please click: https://www.jnsaiwo.com I hope this article can be helpful to you. Thank you for reading!