在隔热断桥铝型材制造中，穿条机机由机体、工作台、滑动板、气动系统、电控盘、传动滚轮等主要组成部分。那具体操作及使用怎么进行呢？下面由有十多年的机器研发经验的济南歌德瑞斯机械设备为您带来穿条机的相关知识。

In the manufacturing of insulated broken bridge aluminum profiles, the threading machine is mainly composed of the body, workbench, sliding plate, pneumatic system, electric control panel, transmission roller, and other main components. How to carry out the specific operation and use? Below, Jinan Gede Ruisi Mechanical Equipment, with over ten years of experience in machine research and development, will bring you relevant knowledge of threading machines.

　　穿条机的正常操作流程：

The normal operation process of the threading machine:

　　1、将设备的电源线接到车间内380伏的空气开关上，检查电路接好

1. Connect the power cord of the equipment to the 380V air switch in the workshop and check that the circuit is properly connected

　　从左边数，左边的三根黑色的是380伏火线、左边第四根黄色的是零线。通电后如果发现“刀盘上升”是反的，那么要将左边的三根黑线任意交叉换一下。调整好电机的方向。

Counting from the left, the three black wires on the left are 380V live wires, and the fourth yellow wire on the left is the zero wire. If it is found that the "disc rising" is reversed after power on, then the three black wires on the left should be crossed and replaced arbitrarily. Adjust the direction of the motor.

　　2、调整和安装好两面的托料平台。

2. Adjust and install the support platforms on both sides.

　　3、先放入一根型材，用手调整该机头的左右移动手轮，将“导向定位块”调整到机器出条槽口和铝型材穿条槽口一致；如需要上下调整则按动“刀盘上升”和“刀盘下降”来调整机头的高度。

3. First, place a profile and adjust the left and right hand wheels of the machine head by hand. Adjust the "guide positioning block" to match the machine's output groove and the aluminum profile's threading groove; If it is necessary to adjust up and down, press "cutter head up" and "cutter head down" to adjust the height of the machine head.

　　4、再放入上面的两根开好齿的铝型材，调整后面托料架子上的“定位板”，顶住铝型材。

4. Put in the two aluminum profiles with teeth on top, adjust the "positioning plate" on the rear support frame, and support the aluminum profiles.

　　5、用人工将隔热条顺导向槽口送入铝型材槽口内一点。

5. Manually guide the insulation strip into the groove of the aluminum profile a little bit.

　　6、踩下设备上的脚踏开关，齿刀加压转动，将隔热条高速送入铝型材槽口，穿条完毕后，松开脚踏开关。

6. Step on the foot switch on the device, pressurize and rotate the toothed blade, and high-speed feed the insulation strip into the aluminum profile groove. After threading, release the foot switch.

　　7、重复以上步骤，加工下一根铝型材。

7. Repeat the above steps to process the next aluminum profile.

本文由穿条机友情奉献.更多有关的知识请点击:https://www.jnsaiwo.com真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

This article is dedicated by the threading machine. For more information, please click: https://www.jnsaiwo.com Sincere attitude. We will provide you with comprehensive service. We will gradually contribute more relevant knowledge to everyone. Stay tuned