复合机就是将两层或者两层以上的材料用粘合剂粘合成为一体。使原有材料得到新的功能。如薄膜和铝箔、薄膜、纸张，无纺布等就经常会用到。亦可和胶片、海绵、布料等复合。常见的软包装材料基本上都是复合成品。下面由有十多年的机器研发经验的济南歌德瑞斯机械设备为您带来穿条机的相关知识，我们应该如何归零穿条机的压盘数字呢？

A laminating machine is a process of bonding two or more layers of materials together with adhesive. Give new functionality to existing materials. Thin films and aluminum foil, thin films, paper, non-woven fabrics, etc. are often used. It can also be compounded with film, sponge, fabric, etc. Common flexible packaging materials are mostly composite finished products. Below, Jinan Gede Ruisi Mechanical Equipment, with over ten years of experience in machine research and development, will bring you relevant knowledge about threading machines. How should we reset the pressure plate number of the threading machine?

　　1. 将溢流阀松开，按下液压启动按钮，观察电机旋向（从上方观察电机应顺时针方向旋转）。若方向不对，请调换三相线的相对位置。注意：本机工作压力为10mpa，在出厂前已调好，非技术人员请不要调动压力阀，以免出现异常，造成无谓损失。

1. Release the relief valve, press the hydraulic start button, and observe the direction of the motor rotation (the motor should rotate clockwise when viewed from above). If the direction is incorrect, please swap the relative positions of the three-phase lines. Attention: The working pressure of this machine is 10mpa and has been adjusted before leaving the factory. Non technical personnel should not adjust the pressure valve to avoid abnormalities and unnecessary losses.

　　2. 将面板上的联动开关置“联动”，将控制面板上的时间继电器调整到一定时间，定位延时调为2s-3s，退刀延时调为3s-4s。

2. Set the linkage switch on the panel to "linkage", adjust the time relay on the control panel to a certain time, adjust the positioning delay to 2s-3s, and adjust the retraction delay to 3s-4s.

　　3. 工件安装与调整：将装好角码的型材置于辅助定位器前方，45度接缝处的外角点对准定位器前面90度角的顶端。按型材高度调整主定位块高度，使之与型材相适应。组角刀具的高度与型材连接的角码高度相适应，当型材内侧凸筋特殊时应更换主定位块，使之能深入到筋间空腔内，不于顶到筋上，因此主定位块设计成活连接，以便用户自行按型材配做各种定位块。

3. Workpiece installation and adjustment: Place the profile with the corner code installed in front of the auxiliary locator, align the outer corner point at the 45 degree seam with the top of the 90 degree angle in front of the locator. Adjust the height of the main positioning block according to the profile height to match it. The height of the corner cutting tool is suitable for the height of the corner code connected to the profile. When the inner convex ribs of the profile are special, the main positioning block should be replaced to allow it to penetrate into the cavity between the ribs and not push against them. Therefore, the main positioning block is designed as a live connection, so that users can customize various positioning blocks according to the profile.

本文内容来自:穿条机 如果您想了解更多关于本行业知识请认准:https://www.jnsaiwo.com，欢迎您的到来！

The content of this article comes from: threading machine. If you want to learn more about this industry, please take a look: https://www.jnsaiwo.com Welcome to come!