济南歌德瑞斯机械设备有限公司

咨询热线:
18678805065
歌德瑞斯

济南歌德瑞斯机械设备有限公司,是窗门制造机器行业的一家集研发、设计、生产、销售、服务为一体的综合性公司。

查看更多+
歌德瑞斯

严格按照行业标准和出口标准组织生产。机器的优良品质和优异性能已被客户广泛认可。同时,公司继续加大对产品研发的投入,以增强产品的核心竞争优势。

查看更多+
歌德瑞斯

严格按照行业标准和出口标准组织生产。机器的优良品质和优异性能已被客户广泛认可。同时,公司继续加大对产品研发的投入,以增强产品的核心竞争优势。

查看更多+
您当前所在位置:首页-新闻资讯-行业动态开齿穿条机操作 >
行业动态

开齿穿条机操作

发布时间:2025-03-28 来源:https://www.jnsaiwo.com/

1.将开齿穿条机设备的电源线接到车间内380伏的空气开关上,检查电路接好

1. Connect the power cord of the toothed threading machine equipment to the 380V air switch in the workshop and check that the circuit is properly connected

从左边数,左边的三根黑色的是380伏火线、左边第四根黄色的是零线。通电后如果发现“刀盘上升”是反的,那么要将左边的三根黑线任意交叉换一下。调整好电机的方向。

Counting from the left, the three black wires on the left are the 380V live wires, and the fourth yellow wire on the left is the neutral wire. If it is found that the "cutter head rising" is reversed after power on, then the three black lines on the left should be crossed and replaced at will. Adjust the direction of the motor.

12

2.调整和安装好两面的托料平台。

2. Adjust and install the material support platforms on both sides.

3.先放入一根型材,用手调整该机头的左右移动手轮,将“导向定位块”调整到机器出条槽口和铝型材穿条槽口一致;如需要上下调整则按动“刀盘上升”和“刀盘下降”来调整机头的高度。

3. First, place a profile and adjust the left and right movement handwheel of the machine head by hand. Adjust the "guide positioning block" to match the machine strip slot and the aluminum profile strip slot; If you need to adjust up and down, press "cutterhead up" and "cutterhead down" to adjust the height of the machine head.

4.再放入上面的两根开好齿的铝型材,调整后面托料架子上的“定位板”,顶住铝型材。

4. Put in the two toothed aluminum profiles on top, adjust the "positioning plate" on the material rack at the back, and press against the aluminum profiles.

5.用人工将隔热条顺导向槽口送入铝型材槽口内一点。

5. Manually guide the insulation strip into the slot of the aluminum profile to a point inside the slot.

6.踩下设备上的脚踏开关,齿刀加压转动,将隔热条高速送入铝型材槽口,穿条完毕后,松开脚踏开关。

6. Step on the foot switch on the device, apply pressure and rotate the toothed knife, and quickly feed the insulation strip into the slot of the aluminum profile. After threading the strip, release the foot switch.

7.重复以上步骤,加工下一根铝型材。

7. Repeat the above steps to process the next aluminum profile.