在隔热断桥铝型材制造中，滚压复合机是一种用于加工铝型材的设备。它主要用于将铝型材的两个部分进行复合，通常是将隔热断桥铝型材的外部铝型材与内部隔热材料（如塑料、橡胶等）进行复合。下面由有十多年的机器研发经验的济南歌德瑞斯机械设备为您带来滚压复合机的相关知识。

In the manufacturing of thermal insulation broken bridge aluminum profiles, rolling composite machines are equipment used for processing aluminum profiles. It is mainly used to composite two parts of aluminum profiles, usually by combining the external aluminum profile of thermal insulation broken bridge aluminum profiles with internal insulation materials (such as plastic, rubber, etc.). Below, Jinan Gede Ruisi Mechanical Equipment, with over ten years of experience in machine research and development, will bring you relevant knowledge of rolling composite machines.

　　1、操作者必须熟悉设备性能和安全规范操作方法。认识所需穿条型材大小面及相对应规格的隔热条。

1. The operator must be familiar with equipment performance and safety regulations and operating methods. Understand the required size, surface, and corresponding specifications of insulation strips for threading profiles.

　　2、工作前应先检查电源和气路情况，和自动运行速度及三刀前后水平。

2. Before starting work, it is necessary to check the power and air circuit conditions, as well as the automatic operating speed and the level before and after the three knives.

　　3、检查所需穿条型材有无变形，掉漆，划伤，色差等缺陷，无问题后穿上对应隔热条。

3. Check if there are any defects such as deformation, paint peeling, scratches, color difference, etc. on the required threading profile. If there are no problems, wear the corresponding insulation strip.

　　4、首先需根据型材需压条位置调节刀具高度和上下距离，固定搁料升降轮。刀具调到正好与穿隔热条槽口水平，转动三个刀具压力轮，压紧型材。力度合适后固定紧。调节固定上面的三个轮，刚好贴上型材上面固定紧之后，试压一支料。

4. Firstly, it is necessary to adjust the height and distance of the cutting tool according to the position of the profile pressing bar, and fix the material lifting wheel. Adjust the cutting tool to be exactly level with the groove of the insulation strip, rotate three cutting tool pressure wheels, and press the profile tightly. Fix tightly after the appropriate force is applied. Adjust and fix the three wheels on top, just press them tightly onto the profile, and then test a piece of material.

　　5、所压好的型材必须是直的，抖动不变形，型材内腔完好。隔热条无破损，型材无破损。

5. The pressed profile must be straight, shake without deformation, and the inner cavity of the profile must be intact. The insulation strip is undamaged, and the profile is undamaged.

　　6、机器运行时，操作者不得穿插机器前后，需调节必须停止运行才可穿行。

6. When the machine is running, the operator must not cross between the front and back of the machine, and must adjust to stop running before passing through.

　　7、手动调节试压好后才可自动批量工作，并时常检查所压型材是否符合工艺要求。

7. After manually adjusting the pressure test, it can automatically work in batches and regularly check whether the pressed profiles meet the process requirements.

　　8、长时间离岗需关掉电源，运行发现故障问题必须停止工作，上报主管。

8. If leaving work for a long time, the power should be turned off. If any problems are found during operation, work must be stopped and reported to the supervisor.

　　9、设备每星期保养一次，加注润滑油，检查配套零件有无松动。

9. The equipment should be maintained once a week, with lubricating oil added and matching parts checked for looseness.

　　10、下班做好设备及周边卫生，关掉电源。

10. After work, do a good job in equipment and surrounding hygiene, and turn off the power.

本文由 滚压复合机 提供技术支持，更多的详细精彩内容请点击我们的网站  https://www.jnsaiwo.com 我们将会全心全意为您提供满意的服务。

This article is supported by the rolling composite machine technology. For more detailed and exciting content, please click on our website https://www.jnsaiwo.com We will wholeheartedly provide you with satisfactory service.