断桥铝型材复合机的工作原理如下：

　　The working principle of the bridge breaking aluminum profile composite machine is as follows:

　　1、准备：，按走线方向将基材各导辊装好，同时将黏剂按比例调整好，启动烘箱的加热系统，当达到相应的设定温度后，再开启传动电机，即可开涂布生产；

　　1. Preparation: Install each guide roller of the substrate according to the wire routing direction, adjust the adhesive in proportion, start the heating system of the oven, and when the corresponding set temperature is reached, then turn on the transmission motor to start coating production;

　　2、涂布：放卷装置的基材先要经过网纹辊，上胶涂布后，再经过烘道进行干澡，即完成涂布工艺；

　　2. Coating: The substrate of the unwinding device needs to go through a mesh roller first, then be coated with glue, and then undergo a dry bath through a drying channel to complete the coating process;

　　3、复合：经EPC气液纠偏进入复合部分，并与第二放卷部分的基材贴合，就实现了复合工艺；

　　3. Composite: After EPC gas-liquid correction, it enters the composite part and adheres to the substrate of the second unwinding part to achieve the composite process;

　　4、冷却收卷：冷却卷之后就完成了基材的整体生产加工。

　　4. Cooling and winding: After cooling the coil, the overall production and processing of the substrate is completed.

　　然后是注意断桥铝型材复合机的使用环境和精良的前期保护。因为断桥铝型材复合机的工作较大，因此应当有用的按期对其做调养，并且还应该给断桥铝型材复合机一个精良的工作环境。要确保断桥铝型材复合机工作在一个清洁的环境中，尽量的让断桥铝型材复合机阔别尘土，同时，应当包管断桥铝型材复合机事情的环境相对枯燥不能湿润，同时不要在断桥铝型材复合机下面板上安排过重的物品，防止环境大概异物对复印机酿成的影响。

　　Then, pay attention to the usage environment and excellent early protection of the bridge breaking aluminum profile composite machine. Due to the large workload of the bridge breaking aluminum profile composite machine, it should be effectively and regularly maintained, and a good working environment should also be provided for the bridge breaking aluminum profile composite machine. To ensure that the bridge cutting aluminum profile laminating machine operates in a clean environment, try to keep it away from dust as much as possible. At the same time, ensure that the working environment of the bridge cutting aluminum profile laminating machine is relatively dry and not humid. At the same time, do not arrange heavy items on the lower panel of the bridge cutting aluminum profile laminating machine to prevent the impact of foreign objects on the copier.

　　在断桥铝型材复合机运行时的各种摩擦力中，凹印滚筒和刮墨刀之间的摩擦力对印刷效果和凹版耐印力影响很大。从微观接触角度建立凹版滚筒和刮墨刀之间摩擦力的动力学模型，通过模型对影响凹版滚筒和刮墨刀之间摩擦力的因素进行了定性的研究，确定了印刷速度、刮刀角度和凹版印刷机振动对凹版滚筒和刮墨刀之间摩擦力影响的规律。

　　Among the various frictional forces during the operation of the broken bridge aluminum profile composite machine, the frictional force between the gravure printing drum and the ink scraper has a significant impact on the printing effect and gravure printing resistance. A dynamic model of the friction force between the gravure cylinder and the ink scraper was established from a microscopic contact perspective. Qualitative research was conducted on the factors affecting the friction force between the gravure cylinder and the ink scraper through the model. The influence of printing speed, blade angle, and vibration of the gravure printing machine on the friction force between the gravure cylinder and the ink scraper was determined.

　　最后，在使用断桥铝型材复合机的时候，不要直接封闭断桥铝型材复合机，而是应当在40分钟左右的时间内，确定没有工作情况时，将复合电机源关掉。这样就可以到达省电的目的，而且确保了断桥铝型材复合机不会频繁的发动。防止复印机由于频仍发动酿成的元件老化和过分消耗。

　　Finally, when using the broken bridge aluminum profile laminating machine, do not directly close the machine. Instead, turn off the composite motor source within about 40 minutes when it is confirmed that there is no working condition. This can achieve the goal of power-saving and ensure that the bridge breaking aluminum profile composite machine does not start frequently. Prevent the aging and excessive consumption of components caused by frequent operation of the copier.

　　本文由 断桥铝型材复合机 友情奉献.更多有关的知识请点击  https://www.jnsaiwo.com   真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is dedicated to the friendship of the Broken Bridge Aluminum Profile Composite Machine. For more related knowledge, please click https://www.jnsaiwo.com Sincere attitude. We will provide you with comprehensive service. We will gradually contribute more relevant knowledge to everyone. Stay tuned